How to Take Ring Doorbell Cover off

If you need to take your Ring Doorbell cover off for any reason, it’s a pretty simple process. All you need is a small Phillips head screwdriver. Just unscrew the two screws on the back of the doorbell (one at the top, one at the bottom), and then pull the faceplate off.

The wires should still be attached to the backplate, so just tuck them in and put the faceplate back on. Screw it in place and you’re good to go!

  • To take the ring doorbell cover off, first locate the two screws on the back of the doorbell
  • Use a Phillips head screwdriver to unscrew the two screws
  • Gently pull the cover off of the doorbell
  • Be careful not to damage or lose any of the small parts attached to the doorbell
  • Once the cover is off, you can access the batteries and other internals of the doorbell
How to Take Ring Doorbell Cover off

Credit: www.youtube.com

How Do I Get My Ring Doorbell Cover off Without Tools?

If your Ring doorbell cover is stuck and you don’t have any tools handy, don’t worry – there’s a way to remove it without causing damage. To remove the cover, start by gently prying up on one side with your fingers. Once you’ve got a small opening, insert a flathead screwdriver or another thin object and carefully wedge it under the edge of the cover.

Continue prying up until the cover pops off. If the cover is still being stubborn, try heating it up with a hair dryer for a minute or so before attempting to remove it again. The heat will help loosen any remaining adhesive holding the cover in place.

How Do You Remove the Faceplate from a Ring Doorbell Pro?

If you need to remove the faceplate from your Ring Doorbell Pro for any reason, here’s how to do it. First, unscrew the two screws at the bottom of the doorbell. Then, use a small flathead screwdriver or a butter knife to pry off the bottom edge of the faceplate.

Once that’s off, you should be able to pull the faceplate away from the rest of the doorbell. Be careful not to lose any of the small parts like screws or washers.

Do I Take Plastic Cover off of Ring Doorbell?

Most people don’t realize that their Ring doorbell comes with a plastic cover already attached. This is to protect the doorbell from the elements and keep it looking new. However, if you’re planning on using your Ring doorbell right away, you’ll need to take the cover off.

Here’s how: 1. Locate the small notch at the top of the plastic cover. 2. Using a flathead screwdriver or a butter knife, gently pry up on the notch until the cover pops off.

3. Set the cover aside and proceed with installing your Ring doorbell according to the instructions in your user manual.

What Screwdriver Do I Need to Open a Ring Doorbell?

There are a few different types of screwdrivers that can be used to open a Ring doorbell. The most common type is a Phillips head screwdriver. Other types of screwdrivers that can be used include flat head and hex head screwdrivers.

To open a Ring doorbell, start by removing the battery cover. There are usually two screws holding the battery cover in place. Once the screws are removed, the battery cover should come off easily.

Next, locate the screws holding the doorbell faceplate in place. There are typically four screws, two on each side of the faceplate. Remove these screws with your chosen screwdriver and set them aside.

Carefully pull off the faceplate to reveal the wires behind it. Locate the two wires that power the doorbell chime. These will likely be red and black in color.

Use a small flathead screwdriver to carefully disconnect these wires from their terminals. Once disconnected, you should be able to remove the entire back plate of the doorbell (including the batteries) without issue.

HOW TO REMOVE THE COVER ON A RING DOORBELL 2

How to Take Cover off Ring Doorbell Pro

If you need to take the cover off your Ring Doorbell Pro, follow these steps: 1. Unscrew the four screws on the back of the doorbell using a Phillips head screwdriver. 2. Gently pull the cover off the back of the doorbell.

3. You should now see the battery compartment and wires. Do not remove any wires or disconnect anything at this time. 4. To put the cover back on, simply reverse these steps.

Conclusion

If you’re having trouble taking your Ring Doorbell cover off, don’t worry – it’s a common problem. There are a few ways to do it, and we’ll walk you through all of them. The first way is to use a flathead screwdriver.

Insert the screwdriver into the tiny hole on the bottom of the doorbell and twist. The cover should come right off. If that doesn’t work, try using a pair of needle-nose pliers.

Grab onto the edge of the cover with the pliers and pull. It may take a little bit of force, but eventually, the cover will come off. The last resort is to use a power drill.

Drill a hole through the center of the doorbell cover and then pry it off with a screwdriver or pliers. Be careful not to damage the wires underneath!

Leave a Comment