Taking off a Ring Doorbell is not as difficult as it may seem. If you’re wanting to take your Ring doorbell off the wall, there are several things that you need to do first. First and foremost, make sure that the power source for your doorbell has been shut off at the breaker box in order to prevent any injury or damage.
Once this is done, there are a few steps involved in taking down your Ring Doorbell safely and efficiently. It’s important to follow these instructions closely so that you can have your device reinstalled without any issues. Firstly, locate all of the screws on the back plate of the doorbell itself; most often they will be located around its perimeter with one screw located directly underneath where it meets up with the mounting bracket.
Unscrew each of these screws using either a Phillips head or flathead screwdriver until they come loose from their respective places within the back plate of the doorbell unit.
- Step 1: Locate the Back Plate of your Ring Doorbell
- This will be mounted on the wall or door frame near where you installed your Ring Doorbell
- Step 2: Place a flathead screwdriver over the back plate, with its tip aligned to the center of one of the four screws that are securing it in place
- Step 3: Turn the screwdriver counterclockwise until you have unscrewed it from its position and then repeat for each remaining screw on the back plate
- Step 4: Once all four screws have been removed, carefully remove them from their slots in order to avoid any damage while taking off your ring doorbell
- Step 5: Carefully pull away from your wall or door frame to separate yourself completely free from your Ring Doorbell’s mount and take off ring doorbell
Easily remove back plate bracket from Ring Video Doorbell
How to Take Back off Ring Doorbell 2
If you’re looking to take back off your Ring Doorbell 2, this guide will provide you with step-by-step instructions on how to do that safely and securely. Taking off the doorbell is a relatively simple process but it does require some preparation and safety precautions.
First, make sure to unplug or turn of any power sources before attempting to take away the doorbell from its mounting surface.
You also want to ensure that you have the right tools for the job; usually either a screwdriver or socket wrench depending on your type of screws. Once everything is ready, start by removing all screws securing the device in place using whichever tool was appropriate for those particular screws.
Once all screws have been removed, carefully slide outwards until there is enough space between the wall and device itself so that it can be lifted up without breaking anything inside.
It may help if someone holds onto one side while another person takes care of lifting up gently on the other end – just use caution when performing this task as too much force could result in damage.
Once taken down from its mountings, disconnecting wires should be done next (if there are any). After making sure no wires are connected anymore, proceed with wrapping it up in an anti-static bag for safe transport if needed or simply store away somewhere safe where moisture won’t reach it over time as water could potentially cause corrosion damage which would render your device unusable after extended periods of exposure.
Finally, reassemble everything once again following these steps but reversed order – i.e., plugging back into power source followed by attaching device firmly onto mounting surface using previously removed screws and ensuring they’re tight enough without overtightening them as doing so can strip threads from their respective surfaces leading potential further problems later down line such as loose connections due lack proper contact being made between two parts during operation due thread stripping issue mentioned earlier..
All said and done!

Credit: support.ring.com
How Do I Get the Back of the Ring Doorbell Off?
If you’re looking to get the back of your Ring doorbell off, you’ve come to the right place! In this blog post, we’ll provide step-by-step instructions on how to properly remove and reattach the backplate of your Ring doorbell.
The first step is to turn off power from the breaker box or disconnect it from its power source.
You will then need a flathead screwdriver or something similar that can fit into the slots located around the edge of your Ring doorbell’s faceplate. Using this tool, carefully pry open each one until all four are loose enough for removal. Make sure not to apply too much pressure as doing so may damage both the plate and device itself.
Once all four screws have been removed, gently pull away at an angle in order for it to be completely separated from its mounting location. Afterward, locate two small tabs near either side of where your wiring connects with your device; these tabs must also be pushed down in order for full removal.
Now that you’ve done this successfully, take note of how everything is connected before unplugging any wires attached to it (i.e., battery pack if applicable).
This way when reinstalling them later on they won’t become mixed up or put in incorrectly which could affect performance/functionality issues once powered up again after completion. You’re now ready to move onto placing a new backplate! To do so simply insert each side into their corresponding slots located near either side before pushing down firmly until secure – make sure not too much force as excessive pressure might cause further damage over time when being used regularly due vibration/movement associated with everyday use .
Finally reattach any wiring connections previously detached prior along with fastening those 4 screws mentioned above beginning process – without forgetting switch breaker/power source back “ON” complete job !
In conclusion , removing & replacing a ring door bell’s back plate is relatively straightforward task but requires some patience & attention detail ensure successful installation . With few simple steps outlined here today should no longer feel intimidated by idea taking yours apart yourself future maintenance needs occur !
How Do You Take the Back off a Ring Doorbell 2Nd Generation?
If you have a Ring Doorbell 2nd generation, you may find yourself needing to take the back off at some point. Whether it’s for changing out batteries or troubleshooting a technical issue, knowing how to safely and effectively remove the back of your device is an important skill. This blog post will walk through all the steps necessary to do so without damaging your doorbell or its components.
The first step in taking off the back of your Ring Doorbell is to locate the release button located on either side of the doorbell. You may need something like a paperclip or small screwdriver to press these buttons in order for them to be released properly. Once both sides are pressed down, slide each piece towards one another until they come apart completely.
If there are any screws holding it together, make sure that these are removed as well before proceeding further with removal process.
Once all pieces have been released from each other, carefully lift up on the top portion and remove it from the bottom half of your doorbell unit. Be sure not to pull too hard on this section as doing so can cause damage to internal components such as wires or boards within it!
Make sure that everything has been disconnected from one another beforehand if applicable – otherwise you may end up causing more harm than good when trying removing/replacing parts inside later down line!
When reattaching this part after servicing/troubleshooting purposes; ensure that all screws are firmly tightened and that no metal objects come into contact with exposed electrical circuits (i.e., power supply) within device itself during assembly process – failure do so could lead potential safety hazards upon use thereafter!
In summary, successfully taking off your Ring Doorbel 2nd generation requires careful attention and patience while going through above mentioned steps – but once done correctly should render successful results every time !
How Do You Take a Ring Doorbell off a Bracket?
If you’ve recently purchased a Ring Video doorbell, you may be wondering how to remove it from its mounting bracket. Fortunately, taking off your Ring doorbell is surprisingly easy and can be done in just a few simple steps.
Before getting started, make sure that the power supply for your Ring doorbell has been disconnected.
This will help prevent any electrical shock or damage when removing the device from its mount.
To start, locate the two small screws located at the top corners of your ring doorbell’s metal faceplate. Using a Phillips head screwdriver, carefully unscrew both screws until they are completely removed from their holes on either side of the plate.
Once these screws have been taken out, lightly pull down on each side of the metal plate to detach it from your ring device itself.
With this faceplate now detached, turn over your Ring doorbell and locate both plastic pins along its sides which hold it into place on its mounting bracket. To remove these pins press gently against them to unlock them before pulling them outwards away from the device with gentle pressure until they become free from their slots in either side of your unit’s body .
With all parts now successfully detached , lift up one end of your ring video doorbell while supporting it firmly with one hand and slowly slide outwards away from its mounting bracket until it becomes completely separated . Now that you’ve successfully taken offyour Ring video Doorbel l ,you should be ableto easily moveit wherever necessary without havingt o re-installthe entire system again !
TakingoffaRingDoorbe llisquickandeasybut ifdoneincorrectlycanresultinseriousdamagebothtotheequipment aswellastoyourselfsoalwaysmake suretodoublecheckthatallconnectionsareproperlydisconnectedbeforeattemptingtomoveordetachanypartsofthesystem!
How Do I Open My Ring Doorbell Without a Tool?
If you’re looking to open your Ring doorbell without a tool, it is possible! All that you need is the proper technique and some patience. This guide will walk you through the steps of opening your Ring doorbell without any tools.
Step 1: Identify which type of installation kit was used for mounting the Ring Doorbell. If either the Screwdriver Kit or Drill/Driver Kit were used, then continue on to step 2. If an Anchor & Screw Kit or Wedge-Kit were used, skip ahead to step 5 as those kits do not require removing screws in order to remove the device from its mountings.
Step 2: Locate and remove all Phillips head screws that are holding the Mounting Plate onto where it has been mounted on (usually a wall). Take care not to strip out these screws with too much torque when taking them out – use only hand strength if necessary and go slowly until they come loose easily. There should be two total screws located near each end of the top edge of this plate – one at each side.
The remaining four corner holes may have anchors instead so make sure there are no hidden anchor pieces before moving on!
Step 3: Once both top-edge screws have been removed, slide off the mounting plate by gripping it firmly with both hands and gently pulling straight away from where it has been mounted on (usually a wall). It should come off fairly easily – if there appears to be resistance then double check for any anchors still in place before attempting again!
Step 4: Now that all hardware has been removed from its spot, locate and carefully unscrew all three Torx T20 Security Screws located around backside rim area of your Ring Doorbell unit itself (this can usually be done with just basic handstrength). Once these are loosened up enough take them out completely – but don’t lose track of them as we’ll need them later when reassembling everything properly!
Step 5: With all three security screw safely removed now comes time for actually getting into our device – grip both sides firmly while using gentle pressure inward toward center button area until casing pops open like butterfly wings revealing internal components inside such as batteries, circuit boards etc… At this point feel free to inspect whatever needs inspecting inside here but remember NOTHING should ever be touched unless absolutely necessary due potential risk factors involved!
Conclusion
Taking off the Ring Doorbell can be a simple process but it’s important to do it correctly. First, you need to make sure that power is disconnected from the doorbell before you start. To do this, you can either disconnect the wires going into the wall or unplug your transformer if one exists.
Next, you will want to use a screwdriver to remove any screws that may be holding the plate on your wall and then gently pull away from your home until it comes loose. Once removed, you should have access to the back of your Ring Doorbell where there are two small holes for releasing pressure in order for removal. Use a flathead screw driver and press down firmly into both holes at once until they click which will unlock the device and allow for easy lifting off of its mounting surface.
Finally, after taking off your ring Doorbell make sure all connections are secure and no wires were damaged during removal so that when reinstalling everything works properly again!