If you have a Ring Doorbell and you want to remove the cover, there are a few things that you need to know. First, there are two types of covers: the faceplate and the backplate. The faceplate is the part that covers the doorbell button, and the backplate is the part that covers the wires.
To remove the faceplate, simply unscrew it from the mounting plate. To remove the backplate, you will need to disconnect the wires from their terminals. Once both plates are removed, you can then access the screws that hold the ring in place.
- Locate the small notch on the bottom of the faceplate
- Insert a small tool, like a paperclip, into the notch and pry up on the plate
- The faceplate should now be loose
- Remove it from the device
- There will now be four screws exposed
- Unscrew these with a Phillips head screwdriver and set them aside
- The cover can now be removed from the device
How Do I Get My Ring Doorbell Cover off Without Tools?
If you need to remove your Ring Doorbell cover without any tools, the process is actually quite simple. The first thing you’ll want to do is locate the small notch on the bottom edge of the cover. Once you’ve found it, insert a flathead screwdriver or a similar tool into the notch and apply pressure until the cover pops off.
Now that you have access to the interior of your Ring Doorbell, there are only two screws holding everything in place. Use a Phillips head screwdriver to remove these screws, and then carefully disconnect the wires (taking note of which wire goes where). With that done, your entire Ring Doorbell unit should now be free from its casing!
How Do I Remove the Faceplate on My Ring Pro Doorbell?
If you need to remove the faceplate on your Ring Pro doorbell, follow these steps:
1. Use a small, flat-head screwdriver to remove the two screws from the back of the doorbell.
2. Carefully pull off the faceplate.
The wires are still attached to the back of the plate, so be careful not to damage them. 3. To reattach the plate, simply line up the holes and screw it back on.
Do I Take Plastic Cover off of Ring Doorbell?
You should take the plastic cover off of your Ring doorbell when you first receive it. This will help ensure that your device is correctly set up and calibrated. Once the cover is off, you can then proceed with the installation process.
How Do I Remove the Ring Video Doorbell 2 Faceplate?
If you need to remove the faceplate on your Ring Video Doorbell 2, it’s actually a pretty simple process. Here are the steps you’ll need to follow:
1. First, unscrew the two screws that hold the faceplate in place.
You’ll find these screws at the top and bottom of the faceplate. 2. Once the screws have been removed, gently pull off the faceplate. It should come off easily, revealing the wires underneath.
3. If you need to access the wires for any reason, simply disconnect them from the terminals. To do this, press down on the small tab at each terminal and then slide out the wire. 4. To put everything back together again, just reverse these steps!
Screw in the two screws and then snap on the faceplate. That’s all there is to it!
HOW TO REMOVE THE COVER ON A RING DOORBELL 2
How to Remove Ring Doorbell Pro Faceplate
If you need to remove the Ring Doorbell Pro faceplate for any reason, here’s a quick and easy guide on how to do it. First, use a small Phillips head screwdriver to remove the two screws that hold the faceplate in place. Next, gently pry the faceplate off with your fingers or a flathead screwdriver.
Be careful not to damage the wires that are attached to the back of the faceplate. Finally, reattach the faceplate by aligning it with the holes and screwing it back in place.
If you need to remove the Ring Doorbell cover for any reason, it’s a pretty simple process. Just unscrew the two screws on the back of the doorbell using a Phillips head screwdriver. Then, pull off the faceplate and set it aside.
To put the cover back on, just line up the holes and screw it back in place.