Removing the faceplate of your Ring Doorbell is a simple process that shouldn’t take more than five minutes. It’s important to make sure you turn off power to the doorbell before attempting this job, as it can be dangerous to work with electricity while it’s still active. Once that’s done, gather a Phillips head screwdriver and any other tools required for the job (like an adapter) so you’re ready to start.
Start by removing the existing screws on either side of the ring doorbell; each one should fit nicely into your screwdriver without too much effort. If there are any issues or if something isn’t working properly, double-check that all connections are secure and nothing has come loose during installation before continuing with removal.
- Step 1: Unscrew the mounting screws – Using a Phillips head screwdriver, unscrew the two mounting screws located at the bottom of the Ring Doorbell faceplate
- Step 2: Gently pull off faceplate – Grasp each side of the faceplate and gently pull it away from wall until it comes off
- Step 3: Disconnect wires- Locate and disconnect any wires that were connected to your Ring Doorbell
- Depending on your setup this may include power supply or chime connecter wire(s)
- Step 4: Remove adhesive tape – Carefully peel off any remaining adhesive tape from both doorbell and wall surface
How to remove the faceplate on your Ring Door Bell
How to Remove Faceplate from Ring Doorbell 1
Removing the faceplate from your Ring Doorbell is essential for a variety of repairs and maintenance tasks. Although it’s not difficult to do, there are some important details you should know before attempting to remove the faceplate. With a few simple steps, you can easily detach the plate and get started on whatever repair or maintenance job needs doing.
Step 1: Unscrew The Faceplate
The first step in removing your Ring Doorbell’s faceplate is to unscrew it from its mounting bracket. To do this, locate two screws at the bottom of the doorbell that serve as mounts for holding it in place.
Use a Phillips-head screwdriver to loosen these two screws until they are completely removed from their brackets. Once this is done, you can carefully slide off the faceplate away from its mounting bracket and set it aside safely out of reach while working on other parts of your doorbell system.
Step 2: Disconnect Wires
Once your Ring Doorbell’s faceplate has been successfully detached, use caution when disconnecting any wires that may be connected behind it—this includes power cables, battery leads (if applicable), wiring harnesses etcetera.. To safely remove each wire without damaging them or any other components within your system, take note of where each one connects before unhooking them all one by one with care and precision using needlenose pliers or tweezers if necessary .
Step 3: Reattach Face Plate
After completing any repairs or maintenance tasks related to why you had initially removed the face plate ,it’s time now reattach back into place -allowing you to restore normal functioning as well as providing an aesthetically pleasing look! Begin by placing both screws back into their respective slots at either side along bottom edges then slowly tighten down until secure in order avoid over tightening which could cause damage/breakage !
Finally connect up all wires again ensuring right connections were made so that everything functions properly once more !
Removing and attaching your Ring Doorbell’s faceplates doesn’t have to be complicated task but following above instructions will ensure smooth process overall -ensuring no issues arise afterwards !

Credit: www.alphr.com
How Do You Remove a Ring Faceplate Without a Tool?
If you’re in a bind and need to remove a ring faceplate without the proper tools, there are still some ways to do it. Removing a faceplate without the right tools can be tricky and time-consuming, so you may want to consider finding an alternative solution if possible. With that being said, here is how you can go about removing your ring faceplate without any special tools:
1. Try using string or dental floss – This method involves looping either string or dental floss around the edge of the plate and then carefully pulling on each end until it comes loose from its mounting brackets. The key is to make sure that the floss remains tight against the plate as you pull. Be careful not to tug too hard as this could cause damage.
2. Use tape – Similar to using string or dental floss, this technique involves wrapping tape around one side of the plate before slowly pulling it along with both hands until it pops off its mounting brackets. As with all methods described here, caution should be taken when doing so as not to cause any unnecessary damage while attempting removal of your ring’s faceplate.
3. Pry with a flathead screwdriver or other thin object – A flathead screwdriver can usually get underneath an edge of a faceplate enough for you to pry upward and loosen up those mounting bracket connections so that they eventually come apart from one another allowing for easy removal of your ring’s faceplate altogether!
Just remember that this method requires extra precaution due to potential damage caused by such force applied directly onto delicate plastic/metal materials used in most rings these days–so please proceed at your own discretion!
In conclusion, removing a ring’s facepalte without any specialized tools gets tricky but certainly isn’t impossible if done properly following one (or more!) steps mentioned above!
How Do You Take the Faceplate off a Ring Doorbell 2?
Taking the faceplate off of a Ring Doorbell 2 is not as difficult as it may seem. With a few simple steps, you can have the faceplate removed in no time. Here’s how to get started:
1. First and foremost, turn off power to the doorbell. You don’t want any electrical shocks while working on your device! Make sure that all power sources are disconnected before beginning work on your unit.
2. Once you have ensured that there isn’t any electricity running through the wires, grab a flat-head screwdriver or other appropriate tool for removing screws from small electronics like doorbells.
3. Now locate the two screws on either side of the faceplate; these should be located near where it connects with the wall or house mounting bracket (depending if your Ring Doorbell 2 is hardwired or wireless). Use your screwdriver to unscrew each one separately until they come out completely and set them aside safely so they won’t get lost during reassembly later on
4. After all screws have been removed, carefully pull away at both sides of the plate until it comes free from its moorings – make sure not to pull too hard though! This will remove both pieces (the ring itself and its backing plate) so that you can now access whatever components need replacing inside such as batteries or wiring connections etc…
5 Finally, once everything has been taken apart successfully put back together again by lining up both parts and pressing firmly until secure; then use your screwdriver again to replace all previously removed fasteners securely into their original positions before turning power back On .
Congratulations -you’ve just taken off & reattached The Face Plate Of Your ring Door Bell 2 !
How Do I Take My Ring Doorbell Cover off to Charge?
If you have a Ring doorbell, chances are that you’ll need to charge it from time to time. Fortunately, charging your Ring doorbell is easy and only requires a few steps. In this blog post, we will go over how to take the cover off of your Ring doorbell in order to charge it.
The first step is to make sure that the power switch on the back of your device is switched off. This can be easily done by flipping the switch up or down depending on which direction turns it off (it should have an “OFF” position). Once this has been done, you can now begin taking off the cover of your device in order to access its battery compartment.
To do this, simply locate where two small tabs are located on either side at the bottom edge of your device’s face plate. You may need a small flat head screwdriver or similar tool for assistance when doing this as sometimes these tabs can be hard to pry open with just fingers alone due to their size and tight fitment against each other – so take care not too apply too much force here!
Once both tabs have been released from their locked positions, carefully lift up and away from the face plate in order to remove it completely – revealing its internal components including its battery compartment underneath; which holds both batteries needed for operation inside (the included USB charger cable should also come out along with this).
Now simply disconnect any cables connected directly into these batteries before removing them entirely; then replace with fresh ones once they’re all taken out!
Reassemble everything back together again after inserting new replacements and reconnecting any associated wiring/cables before putting back onto place- being sure that all screws & fasteners remain tightened securely during installation process as well (referring user manual for guidance if needed) . Finally: flip power switch back ON position when done & enjoy using newly charged Door Bell system!
Conclusion
Hey there! Are you wanting to remove the faceplate from your Ring Doorbell? It’s actually not that hard, and I’m here to help you out.
First off, grab a small flathead screwdriver. You’ll need this in order to remove the two screws on each side of the doorbell unit. Once those are removed, carefully pry up the faceplate with your fingers or a thin object like a butter knife – don’t worry about breaking it as it should easily come off when unscrewed correctly.
Next, locate the reset button which is located underneath the battery compartment at the back of your device – press and hold this button for 10 seconds until you hear a chime sound. This will reset all settings associated with your Ring Doorbell including Wi-Fi connection information so make sure you have these details on hand before doing this step!
Finally, reattach your new faceplate by sliding it into place and then tightening up those two screws again until they’re secure.
That’s all there is to it – now you can enjoy using your newly updated Ring Doorbell without worrying about any pesky facesplates getting in the way!