If you’re like me, you’re probably wondering how to get your Ring Doorbell off to charge. Here’s a quick and easy guide on how to do just that!
First, locate the small black power button on the back of your Ring Doorbell.
Once you’ve found it, press and hold the power button for about 5 seconds. You’ll know the device is off when the light on the front of the doorbell turns from white to red.
Now that your Ring Doorbell is off, it’s time to charge it up!
To do this, simply connect one end of your USB charging cable into the port on the back of the doorbell, and then plug the other end into a power outlet. Make sure that the outlet you’re using is rated for indoor use; outdoor outlets can sometimes cause damage to electronic devices.
Once your Ring Doorbell is plugged in and charging, you’ll see a white light on the front of the device.
This light will turn green once the battery is fully charged, which usually takes around 4-6 hours.
- Unscrew the doorbell from the mount
- Remove the faceplate of the doorbell
- Take out the battery and connect it to a charger
- Once the battery is charged, reattach it to the doorbell and screw it back onto the mount
Credit: www.wikihow.com
How Do I Take My Ring Doorbell off to Charge?
Assuming you have the Ring Doorbell (1st generation), there are four small screws on the back of the device. Two are above the battery compartment and two are below it. Use a Phillips head screwdriver to remove these screws and pull off the faceplate.
There will now be exposed wires. You can simply unplug the doorbell from its wire harness to charge it or to replace the battery.
To charge your Ring Doorbell, you will need to connect it to a power source using the micro USB port on the back of the device.
Once it is connected, you will see a solid white light on the front of your Ring Doorbell indicating that it is charging. It typically takes around 4-5 hours to fully charge your device.
If you need to replace your battery, we recommend using a lithium ion 3.6 volt battery with 1700mAh capacity or higher.
To do this, first disconnect your Ring Doorbell from its wire harness and then open up the battery compartment by pushing down on the tab located underneath where the faceplate was attached and sliding it off. Remove any existing batteries and insert new ones making sure that they are facing in the correct direction (the positive end should be facing up).
Do You Have to Take Your Ring Doorbell off to Charge It?
No, you do not have to take your Ring doorbell off to charge it. There is a built-in battery that can be charged using the included micro USB cable. To charge the battery, simply connect the micro USB cable to the doorbell and plug it into a power outlet.
The battery will take approximately 4-5 hours to fully charge.
How Do You Remove a Ring Doorbell Battery Without the Tool?
If you need to remove your Ring Doorbell battery without the tool, there are a few steps you can follow. First, use a small screwdriver or other sharp object to press the reset button on the back of the doorbell. This will release the battery compartment cover.
Next, use a paperclip or other thin object to press the tab on the battery compartment cover and slide it off. Finally, use a small Phillips head screwdriver to unscrew the two screws holding the battery in place and lift it out.
How to charge Ring video doorbell
How to Remove Battery from Ring Doorbell 4
If you need to remove the battery from your Ring Doorbell 4 for any reason, follow these steps:
1. First, make sure that your doorbell is disconnected from power. If it’s connected to a wired power source, simply unplug it.
If it’s running on battery power, press the button on the back of the doorbell to release the battery.
2. Next, use a small screwdriver or other tool to remove the two screws that secure the faceplate to the doorbell body.
3. With the faceplate removed, you should now see four Phillips head screws holding the battery compartment in place.
Remove these screws and lift off the cover to access the battery inside.
4. To remove the actual battery, first disconnect the positive (red) and negative (black) wires from their terminals. Then, use a small flathead screwdriver to pry up on one end of the battery until it pops out of its slot.
Repeat this process for each of the batteries inside (there are usually two).
Conclusion
If you’re having trouble getting your Ring Doorbell to charge, there are a few things you can try. First, make sure that the charging port on the doorbell is clean and free of debris. If it’s dirty, use a cotton swab or toothpick to gently clean it out.
Next, check the battery itself and make sure that it’s properly seated in the charger. Finally, if you’re still having trouble, try using a different USB cable or charger.
