How to Dismount Ring Doorbell

Angel K. Vanleuven

Updated on:

Ring Doorbells are becoming increasingly popular, as they allow homeowners to be alerted when someone presses the doorbell or triggers motion sensors. These convenient devices are great for security and convenience, but what happens if you need to dismount it? Dismounting a Ring Doorbell is not difficult, however there are some important steps that should be taken in order to ensure its safe removal from the wall.

In this blog post we will discuss how to properly dismount your Ring Doorbell so that your home remains secure. The first step in safely removing your Ring Doorbell is to switch off power supply running through the unit. If you have hardwired version of your unit than turn off breaker supplying electricity into door bell circuit or unplug transformer powering up device.

Doing this ensures that no accidental electrical shock can occur during installation process. Once power is shut off then use screwdriver provided with device kit, unscrew screws holding mounting plate onto wall surface and gently pull away plate from wall while keeping an eye on both sides of ring door bell ensuring none of wires get disconnected mid-way through process.

  • Step 1: Shut off power to the Ring Doorbell
  • Make sure there is no electrical current running through the doorbell before you start taking it apart
  • Step 2: Remove any screws that are connecting the mounting plate to your wall
  • Carefully take out each screw and place them in a safe spot for later use
  • Step 3: Disconnect the wiring from the back of your Ring Doorbell, if applicable
  • Your model may not require this step depending on how it was wired up originally
  • Step 4: Pull gently on the ring doorbell itself until it pops out of its housing or bracket against your wall or door frame where it’s mounted
  • It should come away easily with little effort required on your part, but be careful not to break or damage anything in this process

How to remove an installed Ring Doorbell

How to Remove Ring Doorbell 2 from Wall

Removing a Ring Doorbell 2 from the wall can be a tricky task. If you’ve just purchased one and need to remove it for any reason, or if your current doorbell has been in place for some time and needs replacing, this guide will help make the process as easy as possible. Firstly, before attempting to unscrew anything, make sure that power is turned off at the breaker box.

This ensures that you don’t get shocked while working on the device. Once all electrical power is off, start by removing the outer faceplate of your Ring Doorbell 2 from its mounting bracket (which should be attached to either side of your home’s entryway). To do this unscrew any screws holding it in place with a screwdriver or socket wrench.

Once removed, pull gently away from the wall and set aside until later use. You may now proceed with detaching screws located around both sides of your ring doorbell itself. Again using a screwdriver or socket wrench carefully remove those screws one by one until completely loose then lift away from the wall and disconnect any wires connected between it & its power source behind walls/ceiling etc..

Now separate Ring’s inner shell from their outer casing so that you can access & detach internal components like batteries & other circuitry which are necessary for proper function when reinstalling again elsewhere or simply discarding altogether without damaging them too much – though they’re pretty durable these days! Finally after separating all parts Now discard old bell unit into trash bin; replace broken/missing screws onto existing mountings before finally reattaching new bell unit following instructions included within package documentation provided with purchase date! Congratulations – You have successfully removed your Ring Doorbell 2!

How to Dismount Ring Doorbell


How Do I Take off My Ring Doorbell?

If you’ve recently installed a Ring doorbell, but now want to take it off for any reason, then don’t worry – removing the device is quick and easy. All you need is a Phillips head screwdriver and about 5 minutes of your time. The first step to taking off your Ring doorbell is to remove the faceplate from the wall.

This can be done easily by unscrewing the two screws located in either side of the unit with a Phillips head screwdriver. Once both screws are removed, simply pull away from the wall gently until it comes loose. Next, disconnect all wires connected to your Ring Doorbell.

Depending on how many wires were connected during installation will determine how long this takes as some may require more effort than others when being removed carefully so that no damages occur while unplugging them. After all cords have been disconnected move onto Step 3: Removing The Unit Itself From The Wall Bracket Now that all wires have been detached its time to remove your ring doorbell itself from its bracket against the wall!

To do this simply use an adjustable wrench or pliers if necessary (depending on what type of screws were used) in order to loosen/remove them completely one at a time until they come free from their respective slots within their holes found around where each corner meets at each side of ring doorbell’s frame body respectively.. Finally once everything has been successfully removed reattach any screws or bolts previously loosened before beginning this process back into place – making sure not too over-tighten them as well!

And voila!

How Do I Remove Ring Doorbell Without Tool?

If you have a Ring doorbell installed at your home, it can be an annoying task to remove it. Fortunately, there are some steps that you can take to remove the device without needing any tools. The first step is to turn off power going to the doorbell.

To do this, locate and unplug the transformer that powers the unit or switch off the circuit breaker for that area in your electrical panel. Once done, unscrew any visible screws from around the mounting plate of your Ring Doorbell using a Phillips-head screwdriver if necessary. Now carefully pull out the mounting plate from its place on your wall and disconnect all wires attached behind it.

Next, use a plastic putty knife or spudger tool (or something similar) to gently pry open both sides of the black casing of your Ring Doorbell and detach either side from each other until they come apart completely so as not to damage them while removing them from their position on your wall. Afterward, slide out any existing batteries located inside and set aside with care until ready for disposal later on. Finally, once all components have been removed successfully including those mentioned above along with its mounting bracket hardware pieces such as washers/nuts/bolts etc., dispose of everything responsibly into designated recycling bins provided by local waste collection agencies in accordance with environmental regulations where possible or otherwise according to instructions by manufacturers themselves respective product packaging guidelines if applicable per individual item(s).

Overall, this should help ensure easy removal process when needed without requiring tools whatsoever but always exercise caution throughout entire operation whenever handling potentially hazardous materials such as electronics related products which may lead towards potential injury if handled improperly during DIY installation procedure(s).

How Do You Slide off a Doorbell Ring?

It can be quite annoying when you are in the middle of something and a doorbell rings. Even if you don’t want to answer it, the sound can still interrupt whatever you were doing. Fortunately, there are several ways to get rid of that annoying ring without having to actually open your door and deal with whoever is on the other side.

The first step is to turn off or unplug your doorbell system from its power source so that it won’t ring anymore. Depending on what type of doorbell system you have, this may require unscrewing some screws or removing a cover plate at the point where the wires enter your home. Once done, any ringing should cease immediately as long as no one else has pressed another button somewhere else in your house (such as an interior chime).

If turning off or unplugging your doorbell isn’t an option for whatever reason, then try covering up the bell itself with something like tape or a cloth to muffle its sound. This will not totally eliminate all noise coming from it but should help lower it significantly until you can take action at a more convenient time later on. Finally, if neither of these solutions works for you, then consider installing a motion-activated security camera near your front entrance which will capture anyone who approaches while also alerting them that they are being watched via flashing lights and/or audio cues such as prerecorded messages or alarms sounds – all without making an audible noise inside your house!

This way when someone presses their finger against the bell they’ll know they’re being observed while still allowing you peace and quiet indoors. In conclusion, there are various ways to slide off an unwanted doorbell ring depending on what kind of setup is currently installed at home and how much effort one wants to put into solving this issue once and for all. So next time someone disturbs our peace by pressing down on those buttons outside our doors we can rest assured knowing that we have options available for silencing their intrusion!


If you’re looking to dismount your Ring doorbell, then we’ve got some great news for you. Dismounting this device is surprisingly easy. In fact, it only takes a few simple steps to get the job done!

First, make sure that your doorbell is powered off before attempting any sort of removal. After doing so, use a flathead screwdriver and unscrew the mounting bracket from the wall. Once loosened, simply pull off the faceplate to reveal two wires attached to either side of the back plate – these are responsible for connecting power and transmitting video signals between your doorbell and its associated app.

Unscrew both wires from their respective ports on either side of the back plate and gently remove them from their slots in order to disconnect them entirely. Finally, grab hold of both sides of your Ring doorbell with steady hands and slowly wiggle it out until it pops free from its mountings – just like that; you’ve successfully dismantled your Ring Doorbell!

Leave a Comment