The Ring Doorbell battery can be changed by removing the faceplate and unscrewing the two screws that hold the battery in place. The old battery can then be removed and a new one inserted in its place. The screws can be replaced and the faceplate put back on.
- Unscrew the faceplate of the doorbell with a Phillips screwdriver
- Pull out the battery compartment and disconnect the old battery
- Connect the new battery and reassemble the doorbell
How Do I Change the Battery on a Ring Doorbell?
If you have a Ring Video Doorbell, you may eventually need to change out the battery. Here’s how to do it: 1. First, unscrew the faceplate from the doorbell.
You should see four small screws holding it in place. 2. With the faceplate removed, two more screws are holding the battery cover in place. Unscrew these and remove the cover.
3. Take out the old battery (it will be attached to wires) and insert the new one, making sure that the positive and negative sides are facing correctly. 4. Reattach the battery cover and screw it in place, then reattach the faceplate as well.
How Do You Remove the Battery Cover on a Ring Doorbell?
If you need to remove the battery cover on your Ring Doorbell, there are just a few steps you need to follow. First, use a small Phillips head screwdriver to loosen the two screws on the back of the doorbell. Next, use your fingers or a flathead screwdriver to pry off the battery cover.
Be careful not to damage the doorbell as you do this. Finally, disconnect the wire connector and remove the old batteries. You can now install new batteries and reattach the battery cover.
Is the Ring Doorbell Battery Removable?
The Ring Doorbell is a battery-operated device that can be installed in minutes and requires no wiring or drilling. The battery is removable and can be replaced with a new one if needed. To remove the battery, first unscrew the doorbell from the mounting bracket.
Then, remove the faceplate by gently pulling it away from the base. Finally, use a small Phillips head screwdriver to unscrew the two screws holding the battery in place.
Can You Change the Battery on a Ring Doorbell 2Nd Generation?
Yes, you can change the battery on a Ring Doorbell 2nd generation. The process is relatively simple and only takes a few minutes to complete. Here are the steps:
1. Remove the faceplate of the doorbell by unscrewing the two screws that hold it in place.
2. Use a Phillips head screwdriver to remove the four screws that hold the battery cover in place.
3. Lift off the battery cover and disconnect the old battery from its terminals.
4. Connect the new battery to its terminals and make sure it’s seated properly in its compartment.
5. Replace the battery cover and screw it into place with your screwdriver.
How to Charge Ring Video Doorbell Battery (2nd Generation) | Ring
How to Remove Battery from Ring Doorbell 1
If you need to remove the battery from your Ring Doorbell 1, follow these simple steps:
1. Use a small flathead screwdriver or other blunt object to press the retaining clip on the back of the doorbell.
2. Gently pull the battery out of the doorbell.
3. If there is any adhesive residue on the doorbell, use a cotton swab or other soft cloth to remove it.
4. To re-install the battery, simply reverse these steps.
How to Remove Battery from Ring Doorbell 2
If you need to remove the battery from your Ring Doorbell 2 for any reason, here’s a step-by-step guide on how to do it.
1. First, unscrew the faceplate from the front of the doorbell.
2. Then, use a small flathead screwdriver to gently pry open the casing around the battery compartment.
3. Carefully remove the battery and disconnect it from the doorbell’s power supply.
4. To reassemble, simply reverse these steps. Make sure that the faceplate is screwed on tightly before powering on your doorbell again.
How to Change Battery on Ring Doorbell Pro
If your Ring Doorbell Pro is running low on battery, you may need to change the battery. Here’s how:
1. Remove the faceplate of your Ring Doorbell Pro by unscrewing the two screws at the bottom.
2. Use a small Phillips head screwdriver to remove the three screws that hold the battery cover in place. Be careful not to lose these screws!
3. Carefully remove the old battery and insert the new one, making sure that the positive and negative terminals are oriented correctly.
4. Replace the battery cover and screw it in place with the three screws you removed earlier. Then replace the faceplate and screw it in place with the two screws at the bottom.
Ring Doorbell Battery Replacement
If you’ve been using your Ring doorbell for a while, you may have noticed that the battery isn’t lasting as long as it used to. When this happens, it’s time to replace the battery. Replacing the battery in your Ring doorbell is a pretty simple process.
You’ll just need a few tools and about 10 minutes of time. Here’s everything you need to know about replacing your Ring doorbell battery: What Tools Do I Need?
To replace the battery in your Ring doorbell, you’ll need a small Phillips head screwdriver and a fresh CR123A 3-volt lithium battery. You can find these batteries at most stores that sell electronics or online. How Do I Replace the Battery?
1. First, remove the faceplate of your Ring doorbell by unscrewing the two screws on the backplate. 2. Next, use your screwdriver to loosen the screw holding down the green wire terminal (this is where your power supply connects). Then disconnect the green wire from its terminal post by gently pulling it off (it should come off easily).
3. With the green wire disconnected, twist counterclockwise and pull outwards on the white plastic housing surrounding the black button—the entire housing will come out with ease (as shown in the image below). Doing so will expose both ends of blue and white wires running through sheaths—these are what connect your button to its corresponding terminals (shown in the image below). Gently hold each end of these wires with your thumb and forefinger as you twist their sheaths clockwise until they’re free from their terminals (as shown in image below).
With both wires now loose, carefully pull them free from their sheaths until they’re completely removed (leave about an inch or so of slack so that reinsertion is easier later on). 4 Now would be a good time to take note of how everything was positioned before proceeding—specifically, pay attention to which way around the old battery was inserted as well as which end of each wire was connected to which terminal post (i.e., make sure you remember where everything goes!). Once done, go ahead and insert your new CR123A 3-volt lithium into the empty space where the old one was positioned—be sure to insert it with its positive side facing up!
Conclusion
Most people don’t know how to change the battery in their Ring Doorbell, but it’s a pretty simple process. The first thing you need to do is remove the faceplate from the doorbell. To do this, you’ll need to use a small screwdriver to remove the two screws that hold the faceplate in place.
Once you’ve removed the screws, you can simply pull off the faceplate and set it aside. Next, you’ll see a small black cover on the back of the doorbell. This covers the battery compartment.
Use your screwdriver to remove this cover, and then take out the old battery. You can now insert your new battery and replace the black cover. Finally, just put your faceplate back on and screw it into place.
That’s all there is to changing the battery in your Ring Doorbell!
